Victron ADA010100400 Mains Cord | NEMA 5-15P 2m (6.5ft)
Victron ADA010100400 Mains Cord | NEMA 5-15P 2m (6.5ft)
Genuine Victron · North American 120V
Victron Mains Cord | NEMA 5-15P to Smart IP43 & Compatible Chargers (ADA010100400)
The exact 2-meter North American AC power cord for compatible Victron Smart IP43 chargers with an IEC C14 inlet.
Victron Smart IP43 chargers use a separately ordered country-specific mains cord. The genuine ADA010100400 cord provides the correct NEMA 5-15P wall plug for standard North American 120V outlets, an IEC C13 charger-side connector, and 2 meters of practical reach for a clean, dependable charger installation.
Exact regional power-cord match
Essential Shore Power Connection for North American 120V Systems
Complete your Smart IP43 installation with the correct regional mains cord.
Victron supplies Smart IP43 chargers with a universal IEC C14 AC inlet so installers can choose the correct wall plug for their country. The ADA010100400 is the North American cord option, combining a grounded NEMA 5-15P wall plug with the matching IEC C13 connector used at the charger.
This is an AC mains accessory—not a battery charging lead. It carries wall power from a properly protected 120V outlet to the charger, which then converts that AC power into the controlled DC charging profile required by the connected battery bank.
Standard NEMA 5-15P North American Plug
NEMA 5-15P is the familiar grounded three-prong plug used with standard 120V household, garage, workshop, campground, and protected shore-power receptacles across the United States and Canada.
Exact IEC Connection for Smart IP43 Chargers
The IEC C13 charger-side connector mates with the IEC C14 inlet used by compatible Smart IP43 chargers. The charger's supplied retainer clip can help prevent accidental disconnection at the inlet.
2 Meters of Flexible Reach
At approximately 6.56 feet long, the cord provides practical reach for chargers mounted on nearby walls, electrical boards, equipment cabinets, and protected marine or RV utility spaces.
Region-Specific Genuine Victron Accessory
Victron separates country-specific AC cords from the charger so each installation can use the correct regional wall plug. This part is the North American 120V option.
Removes Generic-Cord Guesswork
Using the exact Victron accessory avoids uncertainty about plug format, grounding, connector fit, cord length, and compatibility with the charger-side retaining arrangement.
Professional Replacement Cord
Use it as the required initial mains cord or as an exact-part-number replacement for a damaged, missing, or misplaced ADA010100400 cord.
Smart IP43 Compatibility Without Guesswork
Verify the charger inlet and part number before ordering.
Current Victron documentation lists ADA010100400 as the NEMA 5-15P, 2-meter mains cord for Smart IP43 chargers. The compatible charger uses an IEC C14 inlet, and the cord terminates in the corresponding IEC C13 female connector.
Some reseller catalogs also associate this cord with compatible Skylla-S chargers. Because charger generations and inlet configurations can differ, confirm the exact Skylla-S model and AC inlet before purchase rather than assuming universal fitment.
Compatible applications
North American Smart IP43 charger installations.
- ✓ Connecting compatible Victron Smart IP43 chargers to standard North American 120V outlets.
- ✓ Completing a Smart IP43 charger installation when the country-specific AC cord was not included.
- ✓ Replacing a lost or damaged ADA010100400 mains cord.
- ✓ RV, marine, golf cart, workshop, garage, cabin, and off-grid charging installations in dry protected locations.
- ✓ Using the Victron Smart IP43 48/13 charger from a suitable 120V shore-power, generator, or utility circuit.
Technical specifications
Exact part number, length, plug type, charger connection, and compatibility.
AC safety and installation guidance
Use a grounded, correctly protected outlet in a dry installation.
- ✓ Inspect the cord, plug, and connector before every installation or replacement.
- ✓ Use only a properly grounded 120V outlet and correctly sized branch circuit.
- ✓ Do not use the cord if the insulation, grounding pin, plug, or IEC connector is damaged.
- ✓ Keep the mains connection dry and protected from spray, standing water, abrasion, and heat.
- ✓ Use the charger’s retainer clip according to its manual where applicable.
- ✓ Do not use adapters that defeat grounding or convert the NEMA 5-15P plug to an incompatible voltage source.
Complete your Smart IP43 charger installation
Pair this mains cord with a compatible Victron Smart IP43 charger.
The ADA010100400 supplies AC input power to the charger; it does not replace the charger, DC battery cables, overcurrent protection, or battery-specific charging configuration. Confirm the charger model, battery voltage, charge settings, AC circuit, and DC installation before commissioning.
Victron ADA010100400 Mains Cord FAQs
Common questions about plug type, charger compatibility, voltage, length, and installation.
Do I really need to buy this mains cord separately?
Yes, if your Victron Smart IP43 charger was supplied without a country-specific AC cord. Victron uses a separate mains-cord system so buyers can select the correct wall plug for their region. ADA010100400 is the 2-meter NEMA 5-15P option for North American 120V outlets.
Will this plug into a normal wall outlet in my house or garage?
Yes. The wall-side connector is a grounded NEMA 5-15P plug, the standard three-prong plug used with common 120V receptacles in the United States and Canada. The outlet and branch circuit must be correctly wired, grounded, and suitable for the connected charger load.
What connector is on the charger side of the cord?
The charger-side connector is an IEC 60320 C13 female connector that mates with the IEC C14 inlet used on compatible Smart IP43 chargers. The charger includes a retainer clip that can help secure the cord at the inlet.
Can I use an old computer or monitor power cord instead?
A generic IEC C13 cord may physically fit, but its conductor size, current rating, approvals, grounding condition, connector quality, and retainer compatibility may be unknown. Using the genuine Victron ADA010100400 removes that uncertainty and provides the correct North American plug and 2-meter length for the intended charger application.
Does this cord work with 240V outlets?
No. The NEMA 5-15P plug is intended for standard North American 120V circuits. Although many Smart IP43 chargers accept a wide AC input range, this specific cord should not be adapted for a 240V receptacle. Use the correct Victron regional or voltage-specific mains cord instead.
Will this cord fit every Victron Smart IP43 charger?
It is intended for Smart IP43 chargers that use the matching IEC C14 AC inlet. Verify the charger model, inlet, label, and Victron documentation before ordering. The current Smart IP43 charger documentation lists the NEMA 5-15P cord as a separately ordered US plug option.
Is this cord compatible with Skylla-S chargers?
Some reseller catalogs describe ADA010100400 for Smart IP43 and compatible Skylla-S chargers, but current Victron catalog language specifically lists it for Smart IP43 chargers. Confirm the exact Skylla-S model and its AC inlet before purchase rather than assuming universal compatibility.
How long is the cord?
The cord is 2 meters long, which is approximately 6.56 feet. That provides practical reach from a wall outlet to a charger mounted on a nearby wall, cabinet, equipment board, or protected utility space.
Is this an outdoor or waterproof power cord?
No formal outdoor or waterproof rating is published for this accessory. Use it only in a dry, protected installation with a properly grounded outlet. The compatible Smart IP43 charger also requires a protected, ventilated location; its connection area is not waterproof.